Browse products from ESDGuns.com for supporting immunity testing to electrostatic discharges on electronic components, subassemblies and products.
Need to transition to IEC 61000-4-2:2025, Edition 3? Contact Us.
ESDGuns.com (Us!)
-
ESDGuns.com VCP Vertical Coupling Plane for Indirect ESD Testing
Utilize the vertical coupling plane with any ESD generator, setup in seconds on any lab bench and begin testing immediately. The indirect radiated portion of electrostatic immunity testing is required for compliance. If your product will be used in metal cabinets, next to industrial machinery or even on top of the metal counters at your corner supermarket, electric shock may cause radiated interference. VCP Vertical Coupling Plane consists of: VCP Aluminum 20" by 20" Wood Stand Ground Cable with 470k Ohm resistors for voltage bleeding
$675.00
-
ESDGuns.com 50mm Insulation Block Set for ISO 10605 Automotive ESD Test Setup
50mm Insulation Block Set for ISO 10605 Ideally suited for the test set-up of table-top equipment for automotive ESD immunity testing per ISO 10605 the Insulation Block Set for ISO 10605 contain pieces 50 mm thick in accordance to the standard. Made of clean polyacrylonitrile with a relative dielectric permittivity of 3.9, surface resistivity of 1014 Ω and a dissipation factor of 0.01.
$775.00
-
ESDGuns.com NIST Calibration Service 15kV RTCA-DO-160 Air Discharge Only
Yearly calibrations are important to keep your ESD generator in good working order, maintaining accurate discharges and a consistent output waveform, as well as extend the life of your test instrument. ESDGuns.com provides rental and calibration packages up to 50% off standard pricing. This keeps your test operation up and running at all times and maintaining a strong quality process. Processing Calibrations Online: Register or Login Process your order through this or another calibration product page An RMA form will be e-mailed after order submission Track progress in your online account Please submit a web request or call us now to inquiry about a rental-calibration package.
$249.00 - $444.00
-
ESDGuns.com Industrial Wood Tripod to mount ESD Simulators
Please note some ESD simulator guns have a screw terminal built into the bottom of the handle, other simulators require a cradle or additional supporting device.
$1,159.00
-
ESDGuns.com Singer-Sensitive Research ESH Electrostatic Voltmeter up to 10kV
The old Singer (Sensitive Research) ESH electrostatic analog voltmeters are suitable for verification of output of your ESD generator. Please note ESD test standards such as IEC 61000-4-2 and ISO 10605 require output discharge to be within 10% and the Singer/Sensitive Research ESH models are not suitable for obtaining those readings. Please see the ESVM meter for a solution with high accuracy capable of meeting todays compliance standards.
$0.00
-
ESDGuns.com Horizontal Coupling Plane for ISO 10605 Automotive ESD Test
Annex F of the actual ISO 10605, provides an additional approach for the ESD powered up test. This approach is intended to produce more repeatable test results and to better correlate with vehicle level ESD tests and the real world environment in comparison especially to the HCP test. This test is an optional test that can be selected by the users in additional to the present standard ESD powered up test as described in clause 5.3. The HCP-auto allows for direct and indirect application of ESD discharges to the DUT as per the automotive test standard ISO 10605 for electrostatic immunity, also reference by manufacturer specs by Ford, GM, Toyota and more. See Diagrams of Horizontal Coupling Plane (Pictures 2 and 3): Field Coupling Plane Field Coupling Strip Discharge islands DUT and wiring harness isolation block DUT DUT wiring harness Battery Peripheral or support equipment AN (if used) Ground reference point for battery and support equipment DUT local ground,(if required) Ground reference point for ESD Coupling Plane, ESD generator and safety ground connection 2 x 470 kΩ high voltage resistors to satety ground HCP ESD generator main uni
$2,450.00
-
ESDGuns.com CST1 1 Ohm ESD Calibration Target per ANSI C63 and MIL
The CST1 ESD calibration target is one of few 1 Ohm targets on the market available to purchase and measure the current waveform from your ESD generator according to ANSI C63, MIL, and a few other niche test standards. ESD Guns CST1 Includes: CST1 Current Target 20 or 30dB Precision Attenuator RG400 Coaxial Cable N to SMA Hard Carrying Case Traceable Calibration Certificate Hardware and Nut Driver
$295.00 - $4,250.00
-
ESDGuns.com EES Electrostatic and Elelectromagnetic Field Sensor
Help stop ESD disturbances with the EES Meter. The EES Meter is capable of providing measurements for many various parameters, which are determined by the type of sensor connected to the meter. Below are the three sensors that the EES comes with: ESD Events Detection The EES Meter serves as a measuring instrument for most ESD signals. The EES Meter measures the volume of ESD events and estimates the events’ magnitude for CDM, HBM and MM models. Electromagnetic Field Measurement The EES Meter is to be transformed into an EMF Meter, Power Density Meter and EIRP Meter. RF Signal Sensor The EES Meter measures the amplitude of an RF signal. Raw Input Resolution: 1mV(1mV-15mV): 15mV (15mV-1500mV) Thresholds: 1-10 Volts, 10-990 Volts Raw input: 1mV and 15 mV ESD Counter Range: 0-32,767 counts (screen count) Electromagnetic Field Peak Range: Min: .001 V/m Max: 20.00 V/M Power Density Meter Peak: Min: .027 nW/cm2 Max: 106.1 uW/cm2 EIRP Meter Peak: Min: .001W Max:5333 W Antenna Factor range: -40.0 to 40 dBm Record interval range: 1 to 360 seconds Record average range: .1 to 360 seconds RF Signal Sensor Unit modes: dBuV, dBm, mV RF Signal Sensor dynamic range: Min: -55 dBm Max: 0 dBm RF Signal Sensor Attenuation: 00 dB/20 dB Accessories Hardcase SD Card SD Adapter 3 Plug adapter Charger BNC M to BNC F Adapter SMA Cable ESD Events Sensor RF Signal Sensor (optional) Electromagnetic Field Sensor (optional) USB-Manual
$299.00
-
ESDGuns.com ESD Generator Current Measurement Setup
Pictured is the first build to comply with edition 3 of IEC 61000-4-2, released in 2025. With customer feedback, it will likely evolve and may look different. Ground cable connection is about complete but not pictured. Order just the ground plane and stand with a pre-drilled hole for the current target, add a shelf, add a shelf with ferrite and absorber, or add an enclosure. Contact us with questions. We will offer retrofit guidance and materials if you ordered a VGP from us in the past two years, it still can be used with a tripod to get data pretty close to the fully compliant setup.
$3,250.00 - $9,850.00
-
ESDGuns.com Robotic ESD Generator/Immunity Test System
Looking to automate your ESD testing finally? Contact us for solutions with a much better up front cost than in the past, easy to use interface for arm and automation setup and control, and much more...
$0.00
-
ESDGuns.com Insulating Support for Wall Mounted Equipment
Non conductive support (wood typically) for testing wall mounted electronics according to IEC 61000-4-2 edition 3. Mounting area is 1.5m by 1.5m to comply for small electronics (under .5m in length and width) and custom sizes are available as well. False walls to reproduce real world scenarios are available to be mounted on the insulating support for the non-conducted surface test.
$0.00
-
ESDGuns.com DM3 Dissipative Mat for ISO 10605 ESD Testing
**If a formal quote is required please export the web page and send through your requisitioning system. We no longer generate formal quotes for orders under $500** Suitable for the test set-up of table-top equipment for ESD immunity per ISO 10605. The DM3 Insulation Support/Dissipative Mat is required for the non-chassis mounted DUT test setup, is 3 mm thick, Resistance 3.1015 Ohm/cm3.
$197.00
Equipment
-
ESD Simulator Guns
-
ESD Immunity Test Environment
-
Calibration Test Equipment
-
Accessories for ESD Guns
-
PCB/IC ESD Immunity Test Systems
-
Automated ESD Test Systems
-
16 kV ESD Guns
-
Resistive Charge Cables
-
30 kV ESD Guns
-
Coupling Planes
-
Electrostatic Voltmeters
-
ESD Calibration Test Targets
-
ESD Test Tables
-
HBM / MM ESD Simulators
-
Insulating Support
-
MIL-STD-331, Munitions & Fuzes (500pF, 500/5000Ohm)
-
Rent 30kV ESD Simulators
