
Batteries, adapters, ground cables, special test trigger fingers and other accessories for ESD guns.
Batteries, adapters, ground cables, special test trigger fingers and other accessories for ESD guns.
Teseq (Schaffner) 171-508 Replacement Battery Charger for Teseq / Schaffner NSG 435 ESD Gun
$249.00
Replacement AC power adapters for Keytek Minizap ESD Simulators MZ-15 and MZ-15/EC models
$199.00
Instead of using the normal battery-pack, a mains power supply unit type Teseq (Schaffner) INA 402 can be used for stationary applications and for longterm test purposes with the Teseq NSG 435 ESD Simulator Gun. The handgrip adapter is an integral part of this power supply unit. It contains electrical components that are necessary for this mode of operation. It is not permissible to operate the NSG 435 with a power supply unit from another system. The power supply unit can be used on all common AC mains supplies without having to make any adjustments, thus: 80 to 240 V (50/60 Hz) with 3-pin IEC connector The power supply unit must be connected to a mains outlet having a protective earth. The protective earth connection does not replace the earth cable for the operation of the Teseq NSG 435. To ensure safe and valid test operation the earth cable must be correctly connected as the pulse return path in every case. The INA 402 mains power supply unit is constructed in conformity with the relevant safety standards and carries the appropriate test symbol
$0.00
Generic Battery Charger for Teseq / Schaffner NSG 435 ESD Gun
$229.00
EM Test PowerPack dito Rechargeable Battery for Dito ESD Gun
$20.00 - $420.00
Run your ESD Tests from a PC For use with Teseq NSG 435 and Teseq NSG 438
$1,795.00
Used to bleed voltages through coupling planes on ESD test setup 2 Meters (6 foot) 470K Ohm - 3 Watt Resistors on Each End
$0.00
Tripod support for Teseq NSG 437 and Teseq NSG 438 pistols. *Tripod not included
$0.00
Please note some ESD simulator guns have a screw terminal built into the bottom of the handle, other simulators require a cradle or additional supporting device.
$1,159.00
EM Test esd.control isn't just a remote control software. It helps you to set-up your test plan and test procedure, guides you through the test telling you which test point is now to be tested and creates a full and detailled report. Try what esd.control can do for you. You will like it. EM Test esd.control Features: Windows 7 and Windows 8 (64Bit) compatibility Support of USB and optical USB interfaces Library of actual basic and generic standards as well as product and product family standards Supports the Bleed-Off function in the tripod test mode Easy-to-use and intuitive creator for test plans and test procedures Enhanced and highly flexible reporting capabilites Up-to-date design and navigation Intuitive operation
$0.00
A remote triggering unit can be connected to operate the NSG 435 inside a Faraday cage with external pulse triggering or for test pulse triggering in synchronism with other conditions. The optical input for remote triggering is insensitive to external light sources. Teseq (Schaffner) INA 415 Remote Triggering Unit for Teseq / Schaffner NSG 435 ESD Gun The normal remote trigger unit consists of a «triggerbox» and 5 m (197 “) of optical cable. The remote trigger works in parallel with the «trigger-button» on the NSG 435. Pulse triggering, or the on/off switching in the case of repetitive discharges, can be effected by a push-button or an electrical signal applied to the triggerbox. The electrical signal at the BNC connector must fulfill the following conditions: On: V = 2.4...10 V, I >2 mA, t >10 ms Off: V <0.8 V Repetition rate: <5 Hz The remote trigger is powered by a conventional 9 volt battery. The current consumption is so low that a battery switch has been dispensed with. If NSG 435 provided with two optical connectors connect the optical cable to the blue terminal. It is recommended to remove the battery if the unit is not going to be used for a long time.
$0.00
You know maybe the inconvenience to wait a long time between ESD tests until the EUT charge has leaked away? How about the uncertainty whether the EUT still carries a residual charge? A simple, safe solution for these problems is the Teseq INA 4430 ESD charge remover designed to be used with the Teseq NSG 437/438 ESD simulators.The charge remover will fully discharge the EUT bringing it to the same reproducible state of discharge each time while reducing the time between tests.Operators can specify opening and closing times between 0.1s and 99s according to their specific requirements. All parameters can be set using the NSG 438’s convenient, easy to read touch panel. Teseq INA 4430 Features: Save time between ESD Tests Remove all residual charge from EUT For use with Teseq NSG 438
$0.00