Store Info

Resources

Manufacturers

Specials

Best sellers

ESD Simulator Guns

ESD Simulation Guns for IEC 61000-4-2, ISO 10605 and other standards to simulate electrostatic discharge phenomena. Pre-certify, troubleshoot or perform any other verification of your product having an ESD gun readily available. With a wide range of simulators up to 30kV, as well as Discharge Networks to meet military and automotive standards - ...

ESD Simulation Guns for IEC 61000-4-2, ISO 10605 and other standards to simulate electrostatic discharge phenomena. Pre-certify, troubleshoot or perform any other verification of your product having an ESD gun readily available. With a wide range of simulators up to 30kV, as well as Discharge Networks to meet military and automotive standards - learn, acquire and receive the best support with this common EMC test.

More

ESD Simulator Guns There are 43 products.

Subcategories

  • 16 kV ESD Guns

    Browse ESD simulators rated to the required voltage levels of IEC 61000-4-2 (8 kV contact discharge and 15 kV air discharge). Most current model 16 kV ESD simulator guns are handheld, light and portable, with some extra voltage capability to allow you to further test and verify the electrostatic withstand immunity of your product. These units are suitable for CE Marking, RTCA/DO-160 and are ready for Mil-STD 461 CS118.

  • 30 kV ESD Guns

    Browse 30kV ESD simulators for ISO 10605, Mil-STD 883 and other high voltage electrostatic immunity test parameters. Current model 30 kV ESD simulators have easy to access and replace discharge networks to allow for specialized ESD capacitance and resistance testing.

  • RC Modules / Discharge Networks

    Discharge Networks or RC Modules (Specific Resistance and Capacitance values) are required for general standards like IEC 61000-4-2, SAE J113 and industry specific standards like ISO 10605. Resistance is referred to in ohms (Ω), Capacitance is referred to in picofarad (pF or "puff"). The most commonly used Discharge Network is for IEC 61000-4-2 and ISO 10605, expressed as 330pF/330Ω. There are over 50 combinations of Resistance & Capacitance depending on the standards and the applicable electronics.

  • Accessories for ESD Simulators

    Batteries, adapters, ground cables, special test trigger fingers and other accessories for ESD guns. 

  • HBM / MM ESD Simulators

    Human Body Model (HBM) and Machine Model (MM) ESD simulators for semiconductor and microprocessor testing to electrostatic immunity. Compliance standards include IEC 60749-26, Mil-STD-883, ANSI/ESD STM5.1-2001, ANSI/ESD STM5.2-1999, JEDEC EIA/JESD22, GB/T17626 IEC61000-4-2 and IEC 61000-4-2 (HMM - Human Metal Model). Additional options for Charged Device (CDM) ESD testing available.

per page
Showing 21 - 30 of 43 items
  • Quick view
    $9,298.00 Used / Refurbished
    1. Meets and far exceeds the requirements in EN/IEC61000-4-2
    2. Up to 30kV output in both contact and air discharges
    3. A light weight discharge gun
    4. Easily changeable capacitor and resistor units
    5. A wide range of options
    6. CE marked
    7. Controllable from an external computer using various communication interfaces.
    $9,298.00
    In Stock
    Request Quote/More Info
    • 10 Volt Steps up to 10 kV
    • LED Spotlight for Electrostatic Discharge Targeting
    • GT-30R Lightweight Discharge Pistol Included
    • Pre-check of high voltage output, withstanding voltage and discharge relay operation
    • IEC 61000-4-2 Standard Test Mode (2 kV, 4 kV, 6 kV, 8 kV Contact; 2 kV, 4 kV, 8 kV, 15 kV Air)
    Typically In Stock
    Request Quote/More Info
    • Voltage range: ±100 to ±30kV
    • Plug-in R/C networks
    • HBM 1500 ohm/100 pf for Mil Std. 883E testing
    • 330 ohm/150 pf (IEC)
    • Custom networks available
    • Contact & air discharge
    • Remote discharge capability
    • Optional E & H-Field Probes
    • Optional IEC Test Target
    • Test in accordance with North American and European ESD simulation standards.

    Typically In Stock
    Request Quote/More Info
    • Built-in self check function with ESD tip terminal to verify discharge relay operation
    • Indicator light confirm discharge (Red to Green)
    • Easily interchangeable Resistance/Capacitance modules
    • LED light to focus and/or illuminate discharging areas
    1 Unit in Stock
    Request Quote/More Info
    • Save time between ESD Tests
    • Remove all residual charge from EUT
    • Charge remover built into the Teseq NSG 438
    Typically In Stock
    Request Quote/More Info
  • Quick view
    $6,950.00 Used / Refurbished
    • 0.20 - 30kV Output Voltage
    • Discharge Interval Programmable from 0.05 to 600 seconds
    • Pre programmed IEC Severity Levels
    • Storage functionality in Manual, Sweep and Program Mode
    $6,950.00
    Request Quote/More Info
    • Touch screen intelligent operation
    • The lowest voltage 5V and 1V step for precise adjusting voltage
    • Available for single or automatic discharge tests and setting times, frequency, etc
    • Meets:
      • ESDA ANSI/ ESD STM5.2-2009
      • JEDEC JESD22- A114E Jan.2007
      • ANSI /ESD-STM5.1 2007
      • MIL-STD-883G 28 Feb.2006
      • ANSI/JEDEC JS-001-2010
      • JEDEC JESD22- A115C Nov.2010
    In Stock
    Request Quote/More Info
  • Quick view
    $299.00 Rental - 1 Month
    • Standards Met:
      • RTCA/DO-160
      • EUROCAE ED-14D
    • Capacitance/Resistance: 150pF / 330ohm
    • Voltage range (CD) Contact Discharge: None
    • Voltage range (AD) Air Discharge: +/- 1kV up to 30kV
    $299.00
    In Stock
    Request Quote/More Info
  • Quick view
    $15,990.00 Used / Refurbished
    • ESD Guns is the only store with this new model in stock
    • Color Touch Display with Activity Log and Self Test
    • Discharges up to 25 Hz
    • 30kV Air and Contact Discharge
    • Switchable Bleedoff/Charge Remover
    • Built-in Activity Log
    • Battery lasts 30,000 discharges at 30kV
    • 80 easy-to-change R/C networks
    • Ideal for ISO 10605, MIL-STD 461G CS118, MIL-STD-331 and many more ESD Standards
    $15,990.00
    Typically In Stock
    Request Quote/More Info
  • Quick view
    $990.00 Rental - 1 Month
    • Flexibility – enables users to meet many different test specifications with maximum cost effectiveness.
    • Quick and simple – one touch operation and simple on screen menu structure.
    • Mobility – the most ergonomic 30 kV ESD gun on the market without an external base control unit.
    • Reliable and economical – A Swiss made product, reliability, service and support in a budget-friendly package.
    $990.00
    Typically In Stock
    Request Quote/More Info
Showing 21 - 30 of 43 items